王昌硕,梁烨,王亮清,沈龙
WANG Changshuo,LIANG Ye,WANG Liangqing,SHEN Long

• 1:中国地质大学(武汉)工程学院
• 2:国核电力规划设计研究院

摘要(Abstract)：

变形模量作为表征岩体变形特征的重要参数,是岩体工程设计的基础力学参数之一。在综合前人研究的基础上提出了基于三维结构面网络模拟确定岩体变形模量的方法,编制了三维结构面网络模拟及计算RQD值的程序。以西南山区某水电站坝址区岩体为实例,在概率统计各组优势结构面几何要素分布形式的基础上,采用Monte Carlo法生成三维结构面网络模型,据此获得岩体三维RQD值,利用RMR法进行质量评价和变形模量的确定,并与钻孔资料统计法和原位试验结果进行对比分析。结果表明:基于钻孔资料统计的估算结果与原位试验相对误差达31.62%,且其估算值偏低;基于三维结构面网络模拟的估算结果与原位试验相对误差仅为2.56%,估算结果精度较高。该方法考虑了岩体质量的空间各向异性,对岩体的质量评价和参数确定更为合理,研究成果为该工程的优化设计提供了合理的计算参数。
As an important parameter to characterize the deformation characteristics of the rock mass, deformation modulus is one of the basic mechanical parameters in rock mass engineering design. Based on previous studies, a method in determining rock mass modulus of deformation is proposed on the basis of three-dimensional discontinuity network simulation method, and then a three-dimensional network simulation program and a RQD values calculation program were completed. Taking the rock mass in a hydropower station dam area located in the southwest of China as an example, a three-dimensional discontinuity network model was generated by using the Monte Carlo method, based on the distribution form of geometric elements of each preponderant discontinuities group from statistical analysis, and thereby obtained three-dimensional RQD values of rock mass. Deformation modulus and the quality of dam area rock mass were then evaluated and compared to drilling data statistics method and in-situ test. The results showed that the relative error between the estimation result based on drilling data statistics and the result of in-situ test is up to 31.62%; the relative error between the estimation result based on three-dimensional network simulation and the result of in-situ test is only 2.56%.This method takes into account of the spatial anisotropy of rock mass quality, which provides a more reasonable evaluation for the rock mass quality and parameter determination, and meanwhile provides reasonable mechanical parameters for optimization design of the project.

关键词(KeyWords)： 变形模量;三维结构面网络模拟;三维RQD;RMR法
deformation modulus;three-dimensional network simulation;three-dimensional RQD;RMR method

Abstract:

Keywords:

基金项目(Foundation): 国家重点基础研究发展计划(973计划)项目(2011CB710604);; 国家自然科学基金项目(41372310);; 中央高校基本科研业务费专项资金项目(CUG090104)~~

作者(Author): 王昌硕,梁烨,王亮清,沈龙
WANG Changshuo,LIANG Ye,WANG Liangqing,SHEN Long

参考文献(References)：

• [1]孙广忠.岩体结构力学[M].北京:科学出版社,1988:1–4.
• [2]宋建波,张倬元,于远忠,等.岩体经验强度准则及其在地质工程中的应用[M].北京:地质出版社,2002:69–71.
• [3]李宁,SWOBODA G.当前岩石力学数值方法的几点思考[J].岩石力学与工程学报,1997,16(5):502–505.LI Ning,SWOBODA G.Discussion on the application of numerical methods to rock mechanics and engineering[J].Chinese Journal of Rock Mechanics and Engineering,1997,16(5):502–505.
• [4]吕爱钟.试论我国岩石力学的研究状况及其进展[J].岩土力学,2004,29(增刊1):1–9.LYU Aizhong.Some situation and progress in rock mechanics study in China[J].Rock and Soil Mechanics,2004,29(S1):1–9.
• [5]邓勇.边坡岩体力学参数反分析遗传一神经网络算法[J].地下空间与工程学报,2007,3(4):751–757.DENG Yong.A genetic-artificial neural network algorithm for mechanical parameters of rock slop[J].Chinese Journal of Underground Space and Engineering,2007,3(4):751–757.
• [6]孙均,蒋树屏,袁勇,等.岩土力学反演问题的随机理论与方法[M].汕头:汕头大学出版社,1996.
• [7]杨林德,朱合华,丁文其,等.岩土工程问题的反演理论与工程实践[M].北京:科学出版社,1996.
• [8]杨志法,王思敬,冯紫良,等.岩土工程反分析原理及应用[M].北京:地震出版社,2002.
• [9]张志刚,乔春生.改进的节理岩体变形模量经验确定方法及其工程应用[J].工程地质学报,2006,14(2):233–238.ZHANG Zhigang,QIAO Chunsheng.Improved empirical method for determination of deformation modulus of jointed rock mass and its application in engineering[J].Journal of Engineering Geology,2006,14(2):233–238.
• [10]DEERE D U.Technical description of rock cores for engineering purposes[J].Rock Mechanics and Engineering Geology,1964,9(1):17–22.
• [11]张永荣,余宏明,殷坤龙,等.江西某厂区边坡岩体结构面网络模拟研究[J].地质科技情报,2000,19(1):85–88.ZHANG Yongrong,YU Hongming,YIN Kunlong,et al.Analog and analysis of discontinuity network of a rock slop in Jiangxi[J].Geological Science and Technology Information,2000,19(1):85–88.
• [12]陈剑平,王清,赵红亮.窗口测线法获取岩体RQD[J].岩石力学与工程学报,2004,23(9):1491–1495.CHEN Jianping,WANG Qing,ZHAO Hongliang.Obtaining RQD of rock mass by sampling window method[J].Chinese Journal of Rock Mechanics and Engineering,2004,23(9):1491–1495.
• [13]GIGLI G,CASAGLI N.Semi-automatic extraction of rock mass structural data from high resolution LIDAR point clouds[J].International Journal of Rock Mechanics and Mining Sciences,2011,48(2):187–198.
• [14]霍俊杰,黄润秋,董秀军,等.3D激光扫描与岩体结构精细测量方法比较研究——以锦屏Ⅰ级水电站为例[J].湖南科技大学学报(自然科学版),2011,26(3):39–44.HUO Junjie,HUANG Runqiu,DONG Xiujun,et al.Comparison analysis on 3D laser scanning technology and refined mesh investigation of rock mass structure[J].Journal of Hunan University of Science&Technology(Natural Science Edition),2011,26(3):39–44.
• [15]ESFAHANI N M,ASGHARI O.Fault detection in 3D by sequential Gaussian simulation of rock quality designation(RQD)case study:Gazestan phosphate ore deposit,Central Iran[J].Arabian Journal of Geosciences,2013,6(10):3737–3747.
• [16]OH S.Geostatistical integration of seismic velocity and resistivity data for probabilistic evaluation of rock quality[J].Environmental Earth Sciences,2013,69(3):939–945.
• [17]GASMI H,HAMDI E,ROMDHANE N B.Numerical homogenization of jointed rock masses using wave propagation simulation[J].Rock Mechanics and Rock Engineering,2014,47(4):1393–1409.
• [18]王国欣,肖树芳,陈剑平.不连续面三维网络在RQD中的应用研究[J].岩石力学与工程学报,2002,21(12):1761–1764.WANG Guoxin,XIAO Shufang,CHEN Jianping.Study on application of 3D network of discontinuities to RQD[J].Chinese Journal of Rock Mechanics and Engineering,2002,21(12):1761–1764.
• [19]贾洪彪,唐辉明,刘佑荣,等.岩体结构面三维网络模拟理论与工程应用[M].北京:科学出版社,2008.
• [20]BIENIAWSKI Z T.Rock mass classifications in rock engineering[C]//BALKEMA A A.Exploration for rock engineering,Proceedings of the Symposium.Geotech Div,Transvaal,Cape Town,S Afr,1977:97–106.
• [21]SERAFIM J L,PEREIRA J P.Considerations on the geomechanical classification of Bieniawski[C]//Soc Portuguesa de Geotecnia and Lab Nacional de Engenharia Civil,Proceedings-International Symposium on Engineering Geology and Underground Construction.Lisbon,Port,1983:II.33–II.42.
• [22]BIENIAWSKI Z T.Engineering rock mass classification[M].New York:John Wiley and Sons,1989:1–251.
• [23]中华人民共和国国家标准编写组.工程岩体分级标准GB50218-94[S].北京:中国计划出版社,1995.
• [24]刘佑荣,唐辉明.岩体力学[M].北京:化学工业出版社,2008:115–128.
• [25]BIENIAWSKI Z T.Determining rock mass deformability:experience from case histories[J].International Journal of Rock Mechanics and Mining Sciences&Geomechanics Abstract,1978,15(5):237–247.
• [26]章广成,李华章,林叶,等.岩体节理体积频率的计算方法及工程应用[J].工程地质学报,2012,20(4):585–590.ZHANG Guangcheng,LI Huazhang,LIN Ye,et al.Assessment of joint volume frequency in rock mass and its application in engineering[J].Journal of Engineering Geology,2012,20(4):585–590.

文章评论(Comment)：